[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Switch for SFP+
Thanks. I am currently using CRS326-24G-2S+ (with routerOS) for this,
but when I want to do vlan trunking through the bonding, cpu load grows
from 3% to more than 90%.
I'm consulting Mikrotik's support in the meantime, because routerOS
probably doesn't take advantage of the switch hardware as swOS would.
El 15/5/20 a las 10:03, Alain Hebert escribió:
> Â Â Â Hi,
>
> Â Â Â Mikrotik is a decent product and I'm always amazed at their
> features set, but...
>
> Â Â Â Using the UI to configuring the switch will punt too much traffic
> toward the CPU. However, it is possible to configure the switch
> fabric with the cli and attain the desired results.
>
> Â Â Â It does not compare to a JNP QFX5100 or a Extreme Network x650,
> x670... etc.
> -----
> Alain Hebertahebert at pubnix.net
> PubNIX Inc.
> 50 boul. St-Charles
> P.O. Box 26770 Beaconsfield, Quebec H9W 6G7
> Tel: 514-990-5911http://www.pubnix.net Fax: 514-990-9443
> On 2020-05-14 15:11, Adam Thompson wrote:
>>
>> Have you actually looked at Mikrotik switches? I don't like the OS,
>> but the hardware does what you want it to.
>>
>> https://mikrotik.com/products/group/switches?filter&s=c&r={%22sfp_plus_interface%22:{%22s%22:%223%22,%22e%22:%2224%22}}#!
>>
>> If necessary, buy your SFP modules from FS.com and get them coded as
>> Mikrotik modules at the factory - that's what we do for Cisco,
>> Brocade, Juniper, Extreme, etc.
>>
>> Even the top-of-the-line Mikrotik only costs US$899.
>>
>> -Adam
>>
>>
>> *Adam Thompson*
>> Consultant, Infrastructure Services
>> [MERLIN LOGO]
>> 100 - 135 Innovation Drive
>> Winnipeg, MB, R3T 6A8
>> (204) 977-6824 or 1-800-430-6404 (MB only)
>> athompson at merlin.mb.ca <mailto:athompson at merlin.mb.ca>
>> www.merlin.mb.ca <http://www.merlin.mb.ca/>
>>
>>
>> ------------------------------------------------------------------------
>> *From:* NANOG <nanog-bounces at nanog.org> on behalf of Mauro Gasparini
>> <mjgasparini at gmail.com>
>> *Sent:* Thursday, May 14, 2020 8:46:21 AM
>> *To:* Mehmet Akcin
>> *Cc:* nanog
>> *Subject:* Re: Switch for SFP+
>> Thank you. The problem is that to get a price lower than U$D 3000 I
>> have to resort to a used device.
>>
>> El 14/5/20 a las 01:08, Mehmet Akcin escribió:
>>> Used Juniper QFX5100-48T will do it. Probably overkill but you can
>>> grab one cheap @ebay
>>>
>>> On Wed, May 13, 2020 at 16:36 Mauro Gasparini <mjgasparini at gmail.com
>>> <mailto:mjgasparini at gmail.com>> wrote:
>>>
>>> Good afternoon.
>>>
>>> I'm looking for a switch with the following capabilities:
>>> . transport for more than 20 gbps
>>> . link aggregation LACP
>>> . slots for SFP+
>>> . seamlessly when trunking vlans through the link aggregation.
>>>
>>> And essentially that doesn't exceed US$D 2000 and is compatible
>>> with
>>> 10GBASE-ER and/or 10GBASE-ZR modules that are not from the
>>> vendor itself
>>> (e.g. SPFs: Huawei, Mikrotik, Sumitomo, OEMs).
>>>
>>> If any of you have a good experience with a device that meets these
>>> requirements (which are minimal with the exception of price and
>>> compatibility) ?
>>>
>>> Regards.
>>> Mauro Gasparini
>>>
>>> --
>>> Mehmet
>>> +1-424-298-1903
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mailman.nanog.org/pipermail/nanog/attachments/20200515/36c4b5c8/attachment.html>